3/30/2023 0 Comments Softraid raid has a caution signRAID 0 - Disk striping is used where speed is the primary objective.Move all the data from the backup location back to the newly created RAID.ĭepending on the RAID controller and the amount of drives, you can select between different RAID modes to setup the disks according to your own requirements.Set your preferred RAID mode and format the drives.Backup all the data from the old drives in a different location.Whenever you change something on an existing RAID, be that installing larger drives or adding additional drives, it's necessary to create a new RAID system. Expanding the storage capacity for an existing RAID For network drives like the M圜loud series, the disks should be installed inside a product that is based on the same firmware and the drives will have to be mounted manually. MacBook Pro and MacBook Air both with OS X 10.9) but it's not possible to access the data from a completely different system (e.g. However, even then, it's important to make sure that the settings are identical and it's best to create a backup of all the data in a different location first, before moving the drives.įor software RAID, the data can be accessed on other computers that are running the same operating system (e.g. The exception to this rule is when both products are based on the same RAID controller and the same firmware version. It's not possible to move the drives to another product without re-formatting the drives. Recovering and accessing data on a RAID arrayįor hardware RAID, the data can only be accessed when the drives are installed in the original product where the RAID was originally created. When you setup a new RAID or change the RAID mode, all existing data is lost! The exception to the rule is Non-RAID but even then, it's better to have a backup than lose data in case something goes wrong during the setup. If you have some existing data on the drives that you intend to use in a new RAID, make sure to backup the data in a different location first. same RAID controller, same power supply). Buying the same RAID enclosure for the second backup unit has the additional benefit that it can act as a backup for the hardware too (e.g. If you currently don't have another backup location and there is not enough space to keep the original data on your computer, consider buying a second RAID enclosure and another set of drives at the same time. Preparing enough storage space may be expensive up front when you need to buy additional drives but if your data is valuable, it is well worth the investment. Doing so makes it possible to easily and quickly recover your data even if you accidentally delete files, the data on that drive gets corrupted, the RAID controller fails or something else happens to your hardware and hard drives (e.g. This could mean that you keep the original data on your computer or make a second backup somewhere else. RAID 1 or RAID 5), it’s always best to keep a second copy of your data in a different location. Even when using a RAID mode with redundancy (e.g. Just because a product supports RAID doesn't mean the data is automatically safe. The RAID is dependent on the operating system and the data cannot be accessed from another system. For direct attached storage drives without RAID controller like the AKiTiO Thunder2 Quad and the AKiTiO Thunder2 Quad Mini, the RAID can be created by the operating system on the computer (e.g. For network drives like the M圜loud series, the RAID is created by the embedded Linux system. Software RAID - There are two types of software RAID. NTFS or HFS+) is recognized by the operating system, you will always be able to access your data. This means that you can move the drive from one computer to the other and assuming that the file system (e.g. The RAID is independent of the computer and the operating system. Hardware RAID - The RAID is created and managed by the RAID controller inside the data storage product. Click the View optional updates option (if available).Important Important information about AKiTiO's hardware and software RAID Software vs hardware RAID.To update a device driver to resolve the yellow exclamation mark on Windows 10, use these steps: You now need to use the Windows Update settings from the Settings app. In the past, you're able to download drivers using Windows Update directly from the Device Manager, but this feature is no longer available. If the device shows a yellow mark, reads "Unknown device," and it's listed under the "Other devices" list, installing the latest device driver through Windows Update may resolve the issue. If you continue to see the error in Device Manager, you want to update the driver to the latest version to resolve the issue with the instructions below. Source: Windows Central (Image credit: Source: Windows Central)Īfter you complete the steps, Windows 10 will reinstall the driver automatically, solving conflicts and other errors.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |